Hi All,

Solaris 7.6.0.1 install keeps failing  I had a similar issue some time ago, however it was not SYMCnbclt. 

Installing SYMCnbclt package.

./cp_to_client: pkgadd: not found

ERROR:   Failed to install SYMCnbclt on testussm01.

         Cannot complete the install.

         Aborting...

See below

$ /usr/local/bin/sudo chmod +x SolarisSPARCtar

$ /usr/local/bin/sudo  gunzip NetBackup-Client-7.6.0.1-Solaris.tar.gz

$ /usr/local/bin/sudo ./SolarisSPARCtar -xvf NetBackup-Client-7.6.0.1-Solaris.tar

./NetBackup_7.6.0.1_CLIENTS1/

./NetBackup_7.6.0.1_CLIENTS1/install

./NetBackup_7.6.0.1_CLIENTS1/VSM_README

./NetBackup_7.6.0.1_CLIENTS1/Doc/

./NetBackup_7.6.0.1_CLIENTS1/Doc/NetBackup_Documentation.pdf

./NetBackup_7.6.0.1_CLIENTS1/LICENSE

./NetBackup_7.6.0.1_CLIENTS1/NBClients/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/catalog/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/catalog/anb/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/catalog/anb/client.inst

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/extract_java

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/client_config

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/tar

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/ssh_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/.sizes

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/client_bin.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/JRE.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/ftp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/sftp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/install_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/cp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/nbj.conf

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/NB-Java.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/nbcheck

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/.sizes_JRE

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/PBX.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/pddeagent.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/.sizes_client_bin

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/pdinstall

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/installpbx

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/.sizes_NB-Java

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10/version

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/extract_java

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/client_config

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/tar

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/ssh_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/.sizes

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/client_bin.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/JRE.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/ftp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/sftp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/install_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/cp_to_client

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/nbj.conf

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/NB-Java.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/nbcheck

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/.sizes_JRE

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/PBX.tar.gz

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/.sizes_client_bin

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/installpbx

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/.sizes_NB-Java

./NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris_x86_10_64/version

$ /usr/local/bin/sudo cd NetBackup_7.6.0.1_CLIENTS1

$ ls

NetBackup_7.6.0.1_CLIENTS1            NetBackup-Client-7.6.0.1-Solaris.tar  SolarisSPARCtar                       sun_exclude

$ cd NetBackup_7.6.0.1_CLIENTS1

$ ls

Doc         install     LICENSE     NBClients   VSM_README

$ /usr/local/sudo ./install

Symantec Installation Script

Copyright 1993 - 2013 Symantec Corporation, All Rights Reserved.

        Installing NetBackup Client Software

Please review the SYMANTEC SOFTWARE LICENSE AGREEMENT located on

the installation media before proceeding.  The agreement includes

details on the NetBackup Product Improvement Program.

For NetBackup installation and upgrade information specific to your

platform and to find out if your installed EEBs or hot fixes are

contained in this release, check out the Symantec Operations Readiness

Tools (SORT) Installation and Upgrade Checklist and Hot fix and EEB

Release Auditor, respectively, at https://sort.symantec.com/netbackup.

Do you wish to continue? [y,n] (y) y

Running preinstall checker...

ok nb_7601_hotfix_auditor: No potential for regression of hotfixes or EEBs was detected.

Do you want to install the NetBackup client software for this client? [y,n] (y) y

This package will install Solaris/Solaris10 client.

This package will install NetBackup client 7.6.0.1.

Enter the name of the NetBackup master server : nbucoreb.my.company.com

Would you like to use "testussm01" as the configured

name of the NetBackup client? [y,n] (y) n

Enter the name of this NetBackup client : testussm01.mycompany.com

Client binaries are located in /var/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10.

Saving client binaries for Solaris/Solaris10.

Installing PBX...

Same version is already installed. Nothing to upgrade for package VRTSpbx

Installation log located here: /var/tmp/installpbx-14906-050115141400.log

Unpacking SYMCnbclt package.

Checking for pre-existing SYMCnbclt package.

Installing SYMCnbclt package.

./cp_to_client: pkgadd: not found

ERROR:   Failed to install SYMCnbclt on testussm01.

         Cannot complete the install.

         Aborting...

========== Unpacking package ==========

x SYMCnbclt.pkg, 509976064 bytes, 996047 tape blocks

x .pkg_defaults, 160 bytes, 1 tape blocks

== Checking for pre-existing package ==

package SYMCnbclt is not installed

========= Installing package ==========

ERROR:   A failure was detected running

         /var/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/net

         backup/client/Solaris/Solaris10/cp_to_client nbucoreb.my.company.com testussm01

         .mycompany.com /tmp/install_trace.14661

File /usr/openv/tmp/install_trace.14661 contains a trace of this install.

That file can be deleted after you are sure the install was successful.

This is the install_trace

$ more install_trace.9946

Symantec Installation Script

Copyright 1993 - 2013 Symantec Corporation, All Rights Reserved.

        Installing NetBackup Client Software

Please review the SYMANTEC SOFTWARE LICENSE AGREEMENT located on

the installation media before proceeding.  The agreement includes

details on the NetBackup Product Improvement Program.

For NetBackup installation and upgrade information specific to your

platform and to find out if your installed EEBs or hot fixes are

contained in this release, check out the Symantec Operations Readiness

Tools (SORT) Installation and Upgrade Checklist and Hot fix and EEB

Release Auditor, respectively, at https://sort.symantec.com/netbackup.

Do you wish to continue? [y,n] (y) y

Running preinstall checker...

ok nb_7601_hotfix_auditor: No potential for regression of hotfixes or EEBs was detected.

Do you want to install the NetBackup client software for this client? [y,n] (y) y

This package will install Solaris/Solaris10 client.

This package will install NetBackup client 7.6.0.1.

Enter the name of the NetBackup master server : nbucoreb.my.company.com

Would you like to use "testussm01" as the configured

name of the NetBackup client? [y,n] (y) n

Enter the name of this NetBackup client : testussm01.mycompany.com

Client binaries are located in /dev/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10.

Saving client binaries for Solaris/Solaris10.

Installing PBX...

Same version is already installed. Nothing to upgrade for package VRTSpbx

Installation log located here: /var/tmp/installpbx-10209-042815181429.log

Unpacking SYMCnbclt package.

Checking for pre-existing SYMCnbclt package.

Installing SYMCnbclt package.

./cp_to_client: pkgadd: not found

ERROR:   Failed to install SYMCnbclt on testussm01.

         Cannot complete the install.

         Aborting...

========== Unpacking package ==========

x SYMCnbclt.pkg, 509976064 bytes, 996047 tape blocks

x .pkg_defaults, 160 bytes, 1 tape blocks

== Checking for pre-existing package ==

package SYMCnbclt is not installed

========= Installing package ==========

ERROR:   A failure was detected running

         /dev/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/net

         backup/client/Solaris/Solaris10/cp_to_client nbucoreb.my.company.com testussm01

         .my.company.com /tmp/install_trace.9946

_____________________------------------------------------

Here is the client server info

$ uname -a

SunOS tesussm01 5.10 Generic_147440-01 sun4v sparc sun4v

$ uname

SunOS

$ uname -r

5.10

$ df -h

Filesystem             size   used  avail capacity  Mounted on

rpool/ROOT/s10s_u10wos_17b

                       133G   6.7G    68G     9%    /

/devices                 0K     0K     0K     0%    /devices

ctfs                     0K     0K     0K     0%    /system/contract

proc                     0K     0K     0K     0%    /proc

mnttab                   0K     0K     0K     0%    /etc/mnttab

swap                    14G   1.9M    14G     1%    /etc/svc/volatile

objfs                    0K     0K     0K     0%    /system/object

sharefs                  0K     0K     0K     0%    /etc/dfs/sharetab

fd                       0K     0K     0K     0%    /dev/fd

rpool/ROOT/s10s_u10wos_17b/var

                       133G    38G    68G    37%    /var

swap                    14G   688K    14G     1%    /tmp

swap                    14G    80K    14G     1%    /var/run

rpool/export           133G    32K    68G     1%    /export

rpool/export/home      133G   2.5G    68G     4%    /export/home

rpool                  133G   106K    68G     1%    /rpool

$ /usr/local/bin/sudo ls -ld /var

drwxr-xr-x  51 root     sys           52 May  1 13:55 /var

$ /usr/local/bin/sudo df -h /var

Filesystem             size   used  avail capacity  Mounted on

rpool/ROOT/s10s_u10wos_17b/var

                       133G    38G    68G    37%    /var

I tried the following  command also same results

/usr/sfw/bin/gtar -xvf <NBU.TAR> to extract the tar file...

$ /usr/local/bin/sudo chmod +x SolarisSPARCtar

$ ls

NetBackup-Client-7.6.0.1-Solaris.tar.gz

SolarisSPARCtar

sun_exclude

$ /usr/local/bin/sudo gunzip NetBackup-Client-7.6.0.1-Solaris.tar.gz

$ ls

NetBackup-Client-7.6.0.1-Solaris.tar  sun_exclude

SolarisSPARCtar

$ /usr/local/bin/sudo /usr/sfw/bin/gtar -xvf NetBackup-Client-7.6.0.1-Solaris.tar                                                                                                                               r

./NetBackup_7.6.0.1_CLIENTS1/

./NetBackup_7.6.0.1_CLIENTS1/install

./NetBackup_7.6.0.1_CLIENTS1/VSM_README

./NetBackup_7.6.0.1_CLIENTS1/Doc/

$ ls

NetBackup_7.6.0.1_CLIENTS1            NetBackup-Client-7.6.0.1-Solaris.tar  SolarisSPARCtar                       sun_exclude

$ cd NetBackup_7.6.0.1_CLIENTS1

$ ls

Doc         install     LICENSE     NBClients   VSM_README

$ /usr/local/bin/sudo ./install

Symantec Installation Script

Copyright 1993 - 2013 Symantec Corporation, All Rights Reserved.

        Installing NetBackup Client Software

Please review the SYMANTEC SOFTWARE LICENSE AGREEMENT located on

the installation media before proceeding.  The agreement includes

details on the NetBackup Product Improvement Program.

For NetBackup installation and upgrade information specific to your

platform and to find out if your installed EEBs or hot fixes are

contained in this release, check out the Symantec Operations Readiness

Tools (SORT) Installation and Upgrade Checklist and Hot fix and EEB

Release Auditor, respectively, at https://sort.symantec.com/netbackup.

Do you wish to continue? [y,n] (y) y

Running preinstall checker...

ok nb_7601_hotfix_auditor: No potential for regression of hotfixes or EEBs was detected.

Do you want to install the NetBackup client software for this client? [y,n] (y) y

This package will install Solaris/Solaris10 client.

This package will install NetBackup client 7.6.0.1.

Enter the name of the NetBackup master server : nbucoreb.my.company.com

Would you like to use "testuiiam01" as the configured

name of the NetBackup client? [y,n] (y) n

Enter the name of this NetBackup client : testussm01.my.company.com

Client binaries are located in /var/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/netbackup/client/Solaris/Solaris10.

Saving client binaries for Solaris/Solaris10.

Installing PBX...

Same version is already installed. Nothing to upgrade for package VRTSpbx

Installation log located here: /var/tmp/installpbx-19260-050115150653.log

Unpacking SYMCnbclt package.

Checking for pre-existing SYMCnbclt package.

Installing SYMCnbclt package.

./cp_to_client: pkgadd: not found

ERROR:   Failed to install SYMCnbclt on testuiiam01.

         Cannot complete the install.

         Aborting...

========== Unpacking package ==========

x SYMCnbclt.pkg, 509976064 bytes, 996047 tape blocks

x .pkg_defaults, 160 bytes, 1 tape blocks

== Checking for pre-existing package ==

package SYMCnbclt is not installed

========= Installing package ==========

ERROR:   A failure was detected running

         /var/strg/NetBackup_7.6.0.1_CLIENTS1/NBClients/anb/Clients/usr/openv/net

         backup/client/Solaris/Solaris10/cp_to_client nbucore2.oit.state.nj.us testuiiam01

         .dol.state.nj.us /tmp/install_trace.18906

File /usr/openv/tmp/install_trace.18906 contains a trace of this install.

That file can be deleted after you are sure the install was successful.

when trying to install BE 15 i get a Fatal error 1606 cannot access network location /SDR/Data

i have previously had BE 2010 installed but has been uninstalled / Removed.

i found this article: https://support.symantec.com/en_US/article.TECH124913.html

but the key does not exist, nor the product as it is a new install since removing the old product.

does anyone have any ideas.

running on server 2k8 64 Bit.

BE 2014 Sp 2

Host Hyper-V server 2012 with 4 server 2012 guests. All have the latest updates. All agents have been updated and are advertising to the backup server.

3 of the guests show all resources while the file server only shows the shares. No other resources are showing up.

I would like to backup only the shares on the file server, but selecting the shares causes the job to fail with "resourses cannot be found"

Credentials at the server level pass, but fail for the shares.

Backing up the whole guest from the host works.

On other servers I am able to chose the volume and select the shares from there. but on this server no volumes are showing up.

The offending server also takes a long time to show the shares when editing the backup job (10 min)

Am at a loss and would appreciate any and all help.

Hi,

I want to know how to archive data in symantec backup exec 2010R3?
 

I just installed BE 2015 at a client and I'm a little confused.  The environement I have at the moment is this:

Dell Physical Server running vmWare esxI host

   1 VM, Windows SBS 2011 standard.

Backup Exec Capacity Edition has been installed in the guest OS VM.     I'm trying to do a backup on the host level along with all GRT options turned on.  The BE agent has been installed on the guest OS.

When the job runs, it immeaditaely returns with "A Backup Exec media server cannot back itself up when it is installed on a virtual machine." (error e0009757).

Sounds simple enough on the face of it, but I can't understand why as this doesn't seem to be indicated in the admin notes anywhere.  It may be implied and I'm just not understanding that, but the way I'm attempting to backup seems to be way it should be done.  Then when I look at the tech note:

https://support.symantec.com/en_US/article.TECH172522.html

Things get a little more confusing because it basically imples that it should work, but might not if non-windows VM's are involved and GRT is turned on. That's not the case here.

So the question is, what way should I be configuring the backup job for this setup.  I should also add that it does contain the tape drive and I have no other physical servers to install this on (there is a second server in the environment, which is a Dell box running 2012 Hyper V with a single 2012 vm, but I was trying to simplify the backup to understand the problem - I will be adding the second server later once I get this first server to backup).

If it should work the way I have it configured (backing up at the host level and then getting meta data via the agent) and the error message is just mis-leading, which I should I be doing /looking for that might be causing the error?   There is only a single vm, so I don't think the tech note would apply.

 Or is it really simply a case of it can't work this way?

Jim.

Hello everyone,

   I just installed BE2014 in a VM client machine using Server2012R2 and discovered that I am not able to see my USB RD1000 disk from the BE storage. Does anyone know how to fix this issue?

When browsing the forums, I frequently see references to old Veratas support documents. For example: http://support.veritas.com/docs/266181

These links no longer resolve & searching for the document ID has not produced useful results. Where can I go to find these documents?

suddenly backup exec 2010 is promppting for password to connect to media server and it wont start. i noticed that the backup exec server is stopped, I tried to start it but get error "the backup exec serveice on local computer started and then stopped, some services stop automatically if they are not in use by other services or programs "
 

Hi, using 7.6.1.  I have some workloads with 2 week retention.  We do a full every week and DINCs every other day.  Mty intention is to have two weeks full recovery from any day during the fortnight.  The DINCs are dependant on the Full preceding them, but I noticed that the full backup from 2 weeks ago expires before the dependant DINCs expire.  This renders the DINCs useless, as I cannot restore from the assiciated full.  Is there a way to keep the associated full until it's DINCs expire, like a setting which says "don't expitre Full backups which have dependant DINCs associated with it"?  I could extend the retention period, but that puts extra pressure on the storage and does not guarantee that the backups are kept if for some reason full backups were unsuccessful.

Thanks.

This is the second week in a row that I received this error. Backups were working fine for months and then I started to receive this error.

Errors:

BackupV-79-57344-65085 - There was a problem running the DBCC.
DBCC results for 'BEDB'.

Exceptions

Backup- server.mydomain.local\BKUPEXECWARNING: "server.mydomain.local\BKUPEXEC\BEDB" is a corrupt file. This file cannot verify.

Verify- server.mydomain.local\BKUPEXEC
WARNING: "BEDB" is a corrupt file. This file cannot verify.

I use BEutility and tried repairing the database. It repairs but when I run a Check DB Consistency I reports error. Any Ideas? What to the BEDB actually do.

This is a 2008r2 server with Backup Exec 2012

Hi,

I am creating SRT on my server whose OS is 3BL652240055_004_RHEL65b.iso.

I used the same iso mounted on /media/isodvd and created the SRT but ran into error:

The media repository is incomplete.
Could not load the following package(s) from distribution media:
    e2fsprogs-libs (e2fsprogs-libs-*.i686.rpm)
    libacl (libacl-*.i686.rpm)
    libattr (libattr-*.i686.rpm)
    libblkid (libblkid-*.i686.rpm)
    libselinux (libselinux-*.i686.rpm)
    libsepol (libsepol-*.i686.rpm)
    libtermcap (compat-libtermcap-2*.i686.rpm)
    libtermcap64 (compat-libtermcap-2*.x86_64.rpm)
    libuuid (libuuid-2*.i686.rpm)
    nspr (nspr-*.i686.rpm)
    pcre (pcre-7*.i686.rpm)
    readline (readline-*.i686.rpm)
V-125-39 caught exception: runtime error in srtPlat.cpp:PackageInfo::verifyRepository()

I deleted the problematic package component names from createsrt.conf file and create the SRT again, but ran into another error liste below.

Can anyone let me know how to do? Thanks in advance.

[root@ming bin]# ./bmrsrtadm

Select one of the following options:

    1.  Create a new Shared Resource Tree.
    2.  Create a new CD image based Shared Resource Tree.
    3.  Copy an existing Shared Resource Tree to a new location.
    4.  Import a Shared Resource Tree.
    5.  Modify an existing Shared Resource Tree.
    6.  Delete an existing Shared Resource Tree.
    7.  List Shared Resource Trees available on this server.
    8.  Quit.

Enter your selection (1-8) [1] : 1
Enter the name of the SRT to create : srt1
Enter the description of the new SRT : srt1

The following media is required:

    Enter the path of first CD/DVD of desired RedHat/Oracle Enterprise Linux Server operating system level . The supported versions are (5 , 6)

Please load the media now.

Load media from (? for help) [/dev/cdrom] : /media/isodvd
Enter the desired architecture (i686 or x86_64) [x86_64] : x86_64
Enter the directory in which to place the new SRT [/export/srt] : /var/images/srt
Creating repository to stow files from distribution media.
Extracting files .............................................................................................. ok.

The following media is required:

    Symantec BMR Third-Party Products CD (3PPCD)

Please load the media now.

Load media from (? for help) [/dev/cdrom] : /var/images/NetBackup
Incorrect volume has been loaded, please try again.
Load media from (? for help) [/var/images/NetBackup] : /var/images/NetBackup/bmr-3ppcd-1.0_275782.iso
Mounting media ... ok.
Working ... ok.

Unmounting media ... ok.
The media repository is now complete.
Working ...................V-125-19 RPM file "/usr/openv/netbackup/baremetal/server/data/media/x86_64-RHEL-618435/e2fsprogs-libs.rpm" does not exist
V-125-39 caught exception: runtime error in srtPlat.cpp:ExtractRpmFiles()
[Error] V-125-105 Cannot install operating system onto this SRT.
Please see diagnostic log for additional information.
Removing SRT "srt1" from server -- please stand by ...
[root@ming bin]# cd /usr/openv/netbackup/baremetal/server/data/media/x86_64-RHEL-618435/
-bash: cd: /usr/openv/netbackup/baremetal/server/data/media/x86_64-RHEL-618435/: No such file or directory
[root@ming bin]# cd /usr/openv/netbackup/baremetal/server/data/media/
[root@ming media]# ls
3PPCD
[root@ming media]#

Thanks,

Lacey

Hi, our customer is using NBU 5230 appliance (2.6.0.3), which works as both master and media server in their environment. All the clients are Windows clients and are backed up to the dedupe disk in the appliance. The appliance has connected to a IBM tape library. They use NetBackup Vault to duplicate backups from the dedupe disk to tape for offsite store. 

Recently they wants to implement KMS in the appliance. I understand that if they back up directly to tapes in the ENCR_xx pool, the backup images will be encrpted. 

My question is:

If they use Vault to duplicate backup images from dedupe disk to the tapes in ENCR_xx pool, will the backup images in the tape be encrypted? Thanks in advance. 

I have windows NT workstation 4.0 sp6 and XP, it's already installed in very old hardware , so i want your opinion to take this windows safe and put it in new hardware like (core i3) by backup or clone or any thing else like we will do it.

so can we do it like i said , because the old hardware (cpu)s are totally different from new (cpu)s.

So my question is can i backup my old system by (Norton Ghost, Acronis backup, Symantec ..etc) and put it in new hardware or new PCs???

So can anybody tell me more detail and more discussion about this ,and what are the problems that i will face it ??

THANK YOUUUU

Hi,

  I need to know how to install Backupexec 2014 CASO. As we have three different location.In all three location we will be having symantec bacup exec 2014. All locations are interconnected via MPLS link. The caso will be installaed in Head office. I would like to know, what is the best way to use CASO. How i can manage all three location sysmatec backup exec server.

Can someone guide me

Regards

Alex

I have a server running Windows Server 2008 R2 enterprise, which is outside the domain, has successfully installed the agent HOWEVER when I do programming tasks to run is not allowing me to see the folders and that I'm working with the account local adminnistrador.

thank you for your help.

attach image.

Hello,

I'm wondering if there is a way to secure communications between the Java console and the 5230 appliance?  Hoping for a TLS session before typing in username and password.

Thanks,

Steve

Hi all.. Current have BE 2010R3 SP3 installed on a Windows Server 2008R2 system with all OS patches installed.  I've been attempting to update the Backup Exec installation to SP4 for an eventual upgrade to Backup Exec 15, but the update to SP4 failes.

When viewing installed hotfixes, Backup Exec only shows SP3.  I have tried to install SP4 via LiveUpdate and by using the standalone SP4 installer, and both fail.  From both the bkupinst.htm file and the MSI logfile, I see instances of "Error 1328" just before the installer rolls back and informs me it fails:

From bkupinst.htm after using Live Update:

05-05-2015,11:52:31 : File: vxmon.exe, Directory: C:\Program Files\Symantec\Backup Exec\, Size: 1397584 
05-05-2015,11:52:31 : ERROR: Error 1328.Error applying patch to file C:\Config.Msi\PT5CC.tmp. It has probably been updated by other means, and can no longer be modified by this patch. For more information contact your patch vendor. 
05-05-2015,11:52:31 : Action ended 11:52:31: InstallExecute. Return value 3. 
05-05-2015,11:52:31 : Action 11:52:31: Rollback. Rolling back action: 

From the MSI logfile after using the standalone installer:

Error 1328.Error applying patch to file C:\Config.Msi\PT279A.tmp.  It has probably been updated by other means, and can no longer be modified by this patch.  For more information contact your patch vendor.  System Error: -1072807676

I have tried a repairing the current installation from Control Panel, and it repairs successfully and have rebooted after that point -- but does not help with the SP4 install.  Any ideas?

Hi all,

one of our Symantec NetBackup master server indicating  dis pools is full over 94%. we are having  over nine  old catalogs, each one is over 6 months old. I was planing to delete multple old catalogs , in order to create additional space. here is the commands I have used .

master server name:/usr/openv/pdde/pdcr/bin#  bpexpdate -recalculate -backupid ( this is backup Id that I find under catalog search window1417928400 ) -d 0 -copy 1

output:

that meet the following criteria:
  backupid         master server name.es1.company name_1417928400
  copy             1

to expire NOW
Continue?(y/n)y
no entity was found            <<<<  error message

If I am usig wrong command, what is the correct one. ?

maybe I am in wrong place to delete old catalog, what is correct path?

this is a output of  folder

master server:/usr/openv/pdde/pdcr/bin # ls

.bin       catalogcaseconvert  crdoreader  crrepair  dcpcrypt          dsiddel  genpo    pddeDR      report62splog  spauser    stat
adler32    cdrinit.sh          crfp        crstat    dcscan            filedel  md5      pddecfg     reroute        spextract  wsget
ca_test    crcollect           crget       crstats   delayscan         fileget  nstpack  pdstresscr  spad           splogscan  wslog
cacontrol  crcontrol           crrecover   dbutil    dr_createlist.sh  fileput  pdconf   prdate      spadb          spoold

Thanks for your time in advance.

greetings.

How I earned my license time?

I have a new NetBackup Appliance 5230 wich was updated to 7.6.1.1 and is configured as a master server and I am triyng to login by my Windows 7 laptop with the Java Console 7.6.1.1, but getting this error : "Unable to login,status:503 Invalid Username". I don't know where is the problem, I added the usernames to the auth.conf file and it looks like:

domain\user.last ADMIN=all JBP=all

domain\user2.last2 ADMIN=all JBP=all

domain\user3.last3 ADMIN=all JBP=all

After configuring auth.conf I did restart services, my nbatd proccess is running normaly.  Can somebody tell me what I am missing?

Thanks,